Pegler Yorkshire Logo

DZR Brass full bore ball valve with lockshield. Female ends, PN25

PB550LS Ball valve

DZR Brass full bore ball valve with lockshield. Female ends, PN25
SizePattern No.Pack 1 QtyPack 2 QtyCodeBarcodePrice (£) each ex VAT
1/2"PB550LS1005022050213013£23.41
3/4"PB550LS1005022050213433£34.54
1"PB550LS505022050213860£52.88
1.1/4"PB550LS155022050561756£79.82
1.1/2"PB550LS125022050561763£105.79
2"PB550LS125022050561787£178.60

PB550LS Ball valve

DZR Brass full bore ball valve with lockshield. Female ends, PN25 dimensions
CodeDescriptionAB
2452601/2" PB550LS59450.21
2452613/4" PB550LS68530.37
2452621" PB550LS80580.57
2452631.1/4" PB550LS95651.15
2452641.1/2" PB550LS100811.21
2452652" PB550LS124882.79
Pegler Yorkshire reserve the right to change specifications
SizePattern No.CodeKv m3/h
1/2"PB550LS24526017.00
3/4"PB550LS24526141.00
1"PB550LS24526270.00
1.1/4"PB550LS245263212.00
1.1/2"PB550LS245264200.00
2"PB550LS245265292.00
Pegler Yorkshire reserve the right to change specifications

Valves and Fittings

Pegler Customcare 5 Year Guarantee - Terms and Conditions

Products are subject to a 5 year guarantee that is between Pegler and the final purchaser of the product.

The guarantee is subject to proof of purchase being supplied.

This guarantee does not affect any statutory rights the consumer may have in law.

The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear and tear.

This product range has been designed for the use of homeowners, domestic and commercial applications and therefore the guarantee is subject to the product being properly selected for their intended service conditions.

The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting instructions.

This is reinforced where valves are covered by the European Pressure Equipment Directive (PED97/23/EC) where Installation, Operating and Maintenance Instructions are supplied with each product and/or carton.

Provided it is installed correctly and receives adequate preventative maintenance it should give years of trouble –free service.

Abusive behaviour and accidental damage to the product are not covered by this guarantee.

The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or consequential damages.

DescriptionMinimum Operating
Pressure (bar)
Maximum Cold Working
Pressure (bar)
Maximum Hot
Working Pressure (bar)
PB550LS Ball valveNo Minimum Operating PressureNo Maximum Cold Working PressureNo Maximum Hot Working Pressure

Care
No regular aesthetic care is required for this product

Maintenance
A regular maintenance program is the most efficient method of ensuring longer term operational efficiency of the selected valve. Such a program would need to include a risk assessment and a planned procedure of how the maintenance will be carried out. The possibility of operational limits being exceeded and the potential hazards ensuring must be considered as part of this assessment. This should be implemented to include visual checks on the valve’s condition and any development of unforeseen conditions, which could lead to failure. The correct fitting tools and equipment should be used for valve maintenance work. Separate means of draining the pipe work must be provided when carrying out any maintenance to valves. Where there may be any system debris this could be collected and /or filtered by installation of the appropriate protective device.

For further help please contact your local engineer.

If your product is under warranty please contact the Service Support Team on: 0800 1560050

Regulations
THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC and CE MARKING
The Pressure Equipment Regulations 1999 (SI 1999/2001) have now been introduced into United Kingdom law.

Valves with a maximum allowable pressure greater than 0.5 bar are covered by these new Regulations. Valves are categorised according to their maximum working pressure, size and rising level of hazard. The level of hazard varies according to the fluid being carried. Fluids are classified as Group 1, dangerous fluids or Group 2, all other fluids including steam. The Categories designated are SEP (sound engineering practice). Valves up to and including 25mm (1”) are designated SEP regardless of the fluid group. Those identified as having increased hazard are Categorised as, I, II, III or IV. All valves designated as SEP do not bear the CE mark nor require a Declaration of Conformity. Categories I, II, III or IV carry the CE mark and require a Declaration of Conformity. Valves classified from the piping chart would not be included in Category IV.

SizePattern No.CodePED Categorisation
1/2"PB550LS245260SEP
3/4"PB550LS245261SEP
1"PB550LS245262SEP
1.1/4"PB550LS245263SEP
1.1/2"PB550LS245264SEP
2"PB550LS245265SEP
Pegler Yorkshire reserve the right to change specifications
ComponentMaterial
BodyDZR brass
BallBrass, chrome plated
StemDZR brass
Stem 'O' ringViton
Seat ringsPTFE (Teflon)
Lever handleSteel
Lever nut (self locking)Zinc plated steel
Tee handle security screwNickel plated brass
Lockshield dust capPlastic
LockshieldBrass
Lockshield security screwBrass
SleeveBrass (EL)
Ext stemBrass (EL)
Fixing screwSteel (EL)
WasherBrass (EL)
SteamWaterOilAirGas InertGas Combustible†Gas Corrosive††Gas Oxygen
yesyesyesyesnononono
Pegler Yorkshire reserve the right to change specifications

Gas application guide
Class 1. INERT Air, argon, carbon dioxide, helium, nitrogen
Class 2. COMBUSTIBLE Hydrogen, methane, natural gas, town gas
Class 3. CORROSIVE Chlorine, sulphur dioxide Class 4. OXYGEN
Class 1. INERT Air, argon, carbon dioxide, helium, nitrogen
† Valves are suitable for British Gas Applications Family Gases 1, 2 and 3.
†† Suitable in applications where moisture is completely absent.